Laserfiche WebLink
1. Standard weight: plain bearing hinge 5PB1 for interior openings through 36 inches wide <br /> without a door closer. <br /> 2. Standard weight: ball bearing hinge 513131 for interior opening over 36 through 40 inches <br /> wide without a door closer, and for interior openings through 40 inches wide with a door <br /> closer. <br /> 3. Heavyweight: 4 ball bearing hinge 513131 HW for interior openings over 40 inches wide, and <br /> for all vestibule doors. <br /> 4. Heavyweight: 4 ball bearing hinge 513131 HWss for exterior openings unless otherwise listed <br /> in groups. <br /> F. Unless otherwise specified, furnish hinges for exterior doors, fabricated from brass, bronze, or <br /> stainless steel. Unless otherwise specified, hinges for interior doors may be fabricated from <br /> steel. <br /> G. Unless otherwise specified, furnish hinges in the following sizes: <br /> 1. PART 26 - 5"x PART 27- 2-1/4" <br /> 5" thick doors <br /> 2. PART 28 - 4- PART 29- 1-3/4" <br /> 1/2"x 4-1/2" thick doors <br /> 3. PART 30 - 3- PART 31 - 1-3/8" <br /> 1/2"x 3-1/2" thick doors <br /> H. Furnish hinge width to accommodate trim and allow for 180-degree swing. <br /> I. Unless otherwise specified, furnish hinges with flat button tips with non-rising pins at interior <br /> doors, non-removable loose pins (NRP) at exterior, and out-swinging lockable interior doors. <br /> J. Unless otherwise specified, furnish all hinges to template standards. <br /> 2.3 CONTINUOUS PIN AND BARREL HINGES <br /> A. Acceptable manufacturers and respective catalog numbers: <br /> Ives Markar Stanley McKinney <br /> 1. PART 32 - Edge Mount Pin & Barrel PART 33- 7 PART 34 - 3 PART 35- 6 PART 36- 3 <br /> Stainless Steel Continuous Hinge 00 Series 00 Series 50 Series 00 Series <br /> 2. PART 37 - Edge Mount Hinge/Guard Pin PART 38- 7 PART 39 - H PART 40 - 6 PART 41 - - <br /> & Barrel Stainless Steel Continuous 05 Series G-305 52 Series ---- <br /> Hinge <br /> 3. PART 42 - Stainless Steel Double Edge PART 43- 7 PART 44 - E PART 45-- PART 46- - <br /> Guard 302 G-308 ---- ---- <br /> B. Hinges shall be independently certified by ANSI for compliance with ANSI A156.26, Grade 1 <br /> (2012). <br /> C. Continuous hinges shall be full height pin and barrel type hinge providing full height door support <br /> up to 600 lbs. Edge mount (unless noted otherwise). <br /> D. Construct hinges of heavy-duty 14-gauge material. The stainless internal pin shall have a <br /> diameter of 0.25 and the exterior barrel diameter of 0.438. <br /> E. Hinge shall be non-handed with symmetrical template hole pattern and factory drilled. Hinge <br /> must accept a minimum of 21 fasteners on the door and 21 fasteners on the frame. <br /> F. Each knuckle to be 2 inch, including split nylon bearing at each separation for quiet, smooth, <br /> self-lubricating operation. <br /> G. Hinge to be able to carry Warnock Hersey Int. or UL for fire rated doors and frames up to 3 <br /> hours. <br /> H. Provide machine screws for doors which have been reinforced to accept machine screws. <br /> I. Note: Fire label for doors and frames should be placed on the header and top rail of fire rated <br /> doors and frames. <br /> Ramsey Water Treatment Plant 0871 00 -5 DOOR HARDWARE <br /> Ramsey, Minnesota <br />