Laserfiche WebLink
A. Contractor to schedule a hardware pre-installation meeting on site to review and discuss the <br /> installation procedures for continuous hinges, locksets, door closers, exit devices, overhead <br /> stops, and electromechanical door hardware. <br /> B. Meeting attendees shall be notified 7 days in advance and shall include: Architect, Contractor, <br /> Door Hardware Installers (including low voltage hardware), Manufacturers representatives for <br /> above hardware items, and any other effected subcontractors or suppliers. <br /> C. All attendees shall be prepared to distribute installation manuals, hardware schedules, <br /> templates, and physical hardware samples. <br /> 1.9 WARRANTY <br /> A. All hardware items shall be warranted against defects in material and workmanship as set forth <br /> in Division One General Requirements. <br /> B. Repair, replace, or otherwise correct deficient materials and workmanship without additional cost <br /> to owner. <br /> PART 2 - PRODUCTS <br /> 2.1 FASTENERS <br /> A. All exposed fasteners shall be Phillips head or as otherwise specified and shall match the finish <br /> of the adjacent hardware. All fasteners ex-posed to the weather shall be non-ferrous or stainless <br /> steel. Furnish correct fasteners to accommodate surrounding conditions. <br /> B. Coordinate required reinforcements for doors and frames. Seek approval of the architect prior to <br /> furnishing through-bolts. Furnish through-bolts as required for materials not readily reinforced. <br /> 2.2 BUTT HINGES <br /> A. Acceptable manufacturers and respective catalog numbers: <br /> Ives StanleyHeger McKinney <br /> 1. PART 1 - Standard Weight, Plain Bearing PART 2- 5 PART 3- F PART 4 - 1 PART 5- T <br /> PB1 179 279 2714 <br /> 2. PART 6 - Standard Weight, Ball Bearing PART 7- 5 PART 8- E PART 9 - E PART 10- T <br /> BB1 B179 B1279 B2714 <br /> 3. PART 11 - Standard Weight, Ball Bearing, PART 12- 5 PART 13- PART 14- PART 15- T <br /> Non-Ferrous BB1 BB 191 131191 B2314 <br /> 4. PART 16- Heavy Weight, Ball Bearing PART 17- 5 PART 18- PART 19- PART 20- T <br /> BB1 HW BB168 B1168 4133786 <br /> 5. PART 21 - Heavy Weight, Ball Bearing, Non- PART 22- 5 PART 23- PART 24- PART 25- T <br /> Ferrous BB1 HW BB 199 B 1199 4133386 <br /> B. Hinges shall be independently certified by ANSI for compliance with ANSI A156.1 (2006). Hinges <br /> shall meet or exceed the following ANSI grade requirements as indicated below: <br /> 1. Standard Weight, Plain Bearing Hinges: Grade 3 <br /> 2. Standard Weight, 2 Ball Bearing Hinges: Grade 2 <br /> 3. Heavy Weight, 4 Ball Bearing Hinges: Grade 1 <br /> C. Unless otherwise specified, furnish the following hinge quantities for each door leaf. <br /> 1. 3 hinges for doors up to 90 inches. <br /> 2. 1 additional hinge for every 30 inch on doors over 90 inches. <br /> 3. 4 hinges for Dutch door applications. <br /> D. Unless otherwise specified, top and bottom hinges shall be located as specified in division 8 <br /> Section "Hollow Metal Doors and Frames". Intermediate hinges shall be located equidistant from <br /> others. <br /> E. Unless otherwise specified, furnish hinge weight and type as follows: <br /> Ramsey Water Treatment Plant 0871 00 -4 DOOR HARDWARE <br /> Ramsey, Minnesota <br />